HAMBENCH PRO · LOOP DIMENSIONS BY PUBLISHED TABLE

Full-Wave Loop Antenna Calculator

Look up full-wave loop dimensions by antenna geometry, frequency, feedpoint impedance, and feedpoint. Choose wire insulation and velocity factor for your build notes; the dimension lookup preserves the published values exactly.

04

PUBLISHED LOOP TABLES

Full-wave loop dimensions

Look up the published dimensions for five loop configurations. The selected wire material and velocity factor are retained as choices but do not alter the published dimensions.

Documented feed pointBottom wire; exact position not specified

PVC (polyvinyl chloride) is the most common plastic insulation in standard installation wire such as PN/RK and speaker cable. Among common plastics, it has the highest dielectric constant and typically gives a velocity factor of approximately 0.92–0.95, so wire is often 5–8% shorter. The effect depends on dielectric constant (εr), insulation thickness and frequency.

Published dimensions are shown exactly as listed. Velocity factor does not adjust them.

Calculations and on-screen results are free. Each printable result PDF costs $2, or is included at no extra cost with an active, paid HamBench Pro monthly subscription ($5/month).

Checking subscription status…

Published dimensions

Horizontal rectangular loop

Horizontal polarization · 14.1 MHz · 50 ohm · Bottom wire; exact position not specified

PVC (Polyvinyl chloride) · VF 0.95

Horizontal rectangular loopFeed point: Bottom wire; exact position not specified. Connect 50 ohm coax directly at the feed point.
Feed pointBottom wire; exact position not specified
MatchingConnect 50 ohm coax directly at the feed point.
Width3.7 m (12.1 ft)
Height7.4 m (24.3 ft)
Frequency MHz14.1
wire length22.2 m (72.8 ft)
width3.7 m (12.1 ft)
height7.4 m (24.3 ft)
2 : 1 SWR bandwidth MHz0.32
1.5 : 1 SWR bandwidth MHz0.18

Installation notes

  • These loop designs use specific wire sizes and heights over typical ground. Results can vary with wire diameter, insulation, height, ground, corner tie-offs and the feedpoint insulator.
  • These published dimensions are starting values for final tuning in the actual installation. Shortening the wire raises resonant frequency; lengthening it lowers resonant frequency.
  • Only listed frequencies are provided for each shape. Do not scale a row or treat an unlisted frequency as a published value.
  • 1 mm (AWG #18) bare wire; top of loop about 3/4 wavelength above ground, with bottom at about half the top height.
  • 2 mm (AWG #12) wire shifts resonant frequency up about 0.5% for the same wire length; larger tubing or rods on the horizontal portions require a little more height.
  • Feed point is on the bottom wire.
  • The design assumes bare wire. Selected material: PVC (Polyvinyl chloride). No material or velocity-factor correction is applied to listed dimensions.
  • Velocity factor is retained as a user choice, but it never changes a listed value.

HAMBENCH PRO · $5 / MONTH

Save and load private station profiles.

Keep multiple station setups with every antenna, coax and battery input, then reopen a profile on any calculator page to refill its matching fields. Calculator use and result viewing stay free.

Checking HamBench Pro access…

Estimates are starting points for station planning; verify antenna tuning, actual feedline loss and battery performance in your setup.

Return to HamBench Pro

Choose a full-wave loop geometry and feedpoint

Compare the available horizontal and vertical loop configurations, select a listed frequency and feedpoint impedance, and review the feedpoint position and matching notes. The page includes the loop dimension diagram in the result PDF for an eligible HamBench Pro member.

Exact dimension lookup with clear missing-row feedback

This tool looks up dimensions from its published table data. A matching row is shown with its listed dimensions; when an exact geometry, frequency, and impedance combination is missing, the calculator says so and may show nearby rows for reference. It does not invent, interpolate, or extrapolate loop dimensions for a missing combination.

The published Practical Antennas tables include rows from 1.85 MHz through 50.5 MHz for selected loop designs and feed impedances. Although the requested coverage reaches about 500 MHz, the source tables stop at 50.5 MHz, so this lookup only offers frequencies with published rows. See the Practical Antennas loop dimension tables for the original data and design notes.

Record wire insulation and velocity factor

Select the insulation material and velocity factor to include them with your loop calculation notes. These choices do not change a published dimension row. Treat the table as a build reference and account for the actual installation, supports, surroundings, and antenna tuning.